Spills should be wiped up immediately, and food should never be left to sit. Marble should be washed regularly with a mild detergent and warm water, but don’t use an abrasive detergent or cleaner since this could leave scratches on the surface. If there is a lot of dust or dirt on the surface, rinse out the brush or sponge frequently to avoid spreading the dirt around or rubbing it deeper into the pores. This minimizes the likelihood of stubborn streaks and simplifies rinsing.
In addition to regular cleaning, marble surfaces subjected to hard wear – such as table tops, counter tops, vanities – should also be protected with a coat of white paste wax or one of the special sealers sold for marble. Before using a sealer, however, test first to see if it will darken the color. In each case, after the poultice is applied, it should be covered with a piece of plastic kitchen wrap that is then taped down with masking tape. Apply a heavy layer (about a half-inch thick) over the stained area, then add a few drops of household ammonia to the paste. Remove the plastic and the poultice, then wash off with warm water. Thoroughly wash off all the material causing the stain, then wash the surface with household ammonia and rinse with plenty of hot water.
Cover promptly with plastic as described above (acetone evaporates very rapidly and is also highly flammable), and leave this in place for at least 24 hours. Spread this over the stained area in a thick layer, then cover with damp cloths. If the surface is merely dull, waxing may be all that is needed to restore the luster. Probably the best procedure, if possible, is to take the marble to a dealer so it can be done by machine. Continue buffing until the etch marks disappear, then rinse with water and wipe dry. The radiator in my bathroom needs painting because the old paint is chipping and there are rust spots in the metal, plus lots of dirt. If you cannot find one of these, buy an inexpensive three-inch brush and use masking tape to attach a stick about 10 inches long to the handle. Questions of general interest will be answered in this column; unpublished letters cannot be answered individually.
The most important step in the maintenance of marble is keeping it clean. Even newspapers and magazines can cause stains, especially when wet or damp. Wet the marble with plain water first, then scrub with a soft brush or sponge and rinse with lots of water.
When cleaning a vertical surface, such as the front of a marble fireplace, it is best to work from the bottom up so dirty water runs down onto a wet surface that has already been cleaned. Do not use wax on surfaces where food will be prepared or on floors. The type of liquid agent to use will depend on the type of stain.
This keeps the paste from drying out too fast so it will keep working that much longer. Use a poultice of 20 percent hydrogen peroxide (hair bleach) mixed with the whiting to form a thick paste. Cover with plastic as described above, then leave in place for at least 24 hours. If the stain is lighter but still noticeable, repeat the application. They are often very difficult to remove since the grease or oil penetrates the surface more than other stains do. Remove the poultice by rubbing with a dry cloth, and repeat the process if some stain still remains. If noticed promptly and if the surface has been properly waxed, the stain can often be rubbed off with a dry cloth.
If the marble has been waxed and the surface has not been neglected for too long, the smoke or soot can usually be washed off with detergent and warm water. If stains persist, cover with a poultice made by mixing baking soda with fresh liquid laundry bleach to form a thick paste. Leave it in place overnight, then wash it off with water or scrape it off with a wood or plastic spatula.
Where a poultice has been used, the surface may also have been dulled or slightly etched. However, if the surface has also been etched (you can feel this with your fingertips), polishing will be necessary to restore the luster. Use a vacuum and any kind of brush with a long handle to reach between the sections for scrubbing out the dirt. Allow this to dry overnight, then apply a flat or low-luster paint in the color of your choice (do not use a gloss).
4 Important Tips For Cleaning Your Limestone Fireplace by limestone.com
If you have a specific limestone cleaner that is a step in the right direction. Acid-based cleaners will damage your limestone because it will cause it to corrode over time since limestone is a porous, sedimentary rock. To clean this mess, first use a vacuum regularly to pick up the excess soot.
You can also use your limestone cleaner or mild soap to scrub away extra tough spots and rinse with water. Whether you make your own alkaline-based poultice or buy one, they will work to take out the oils and stains without destroying the limestone. Sealing your limestone every year is the best way to preserve and protect it from any future stains.
But do you know the best way to clean it and keep it in good condition? Make sure that you check the labels of any cleaning products you want to use on your limestone. Then take a soft cloth or rag (nothing with a scratchy or abrasive surface) and get it damp with water to wipe the soot away.
Make sure that after you wipe down your limestone with the cleaning product that you fully rinse with water and dry the area when you are finished.
Yet, before you use any stain remover make sure that it is made for limestone, as many are not alkaline-based.
Quick and Easy Ways To Remove Soot and Ash From Your Fireplace by goodhousekeeping.com
A wet/dry vacuum with a disposable bag will handle the job, once the pile has cooled for at least four days. Discard the mess outside, ideally in a metal trash container, but definitely away from your house. To remove light soot or a cloudy film from glass doors, mix a solution of equal parts white vinegar and warm water and pour into a spray bottle.
If soldered-on gunk won’t budge (and if you really care), scrape it away with a razor blade. If you have smoke stains on your fireplace facing, begin by squirting them with water — it’ll keep the cleaning solution from soaking in too fast (this is particularly important with brick).
Spritz a bit on a paper towel and dip it into the fireplace ashes to use as a gentle abrasive (smart, right?). For marble or other stones, squirt with water, then go over with a soft cloth dipped in mild dishwashing liquid and water.
How To Clean Marble Fireplaces and Surrounds by direct-fireplaces.com
Marble is a very durable material, but it’s porous and can be susceptible to staining, particularly from acidic materials. This guide will tell you how to clean a marble fire surround and fireplace to keep it looking as good as new. Lightly rub the stain with the cloth, increasing in pressure if the stain is stubborn. Use distilled water where possible as any impurities in the water can stain the marble. Avoid using white vinegar or limescale removers as they contain acids, or baking soda which is abrasive and could affect the finish of the marble. Cover the poultice with plastic sheeting of some kind (a piece of plastic bag would do it) and tape down. Browse our range of marble fireplaces and marble fire surrounds today, or contact us if you have any questions about cleaning and maintaining them.
Whether your home is traditional or contemporary you’ll find your perfect choice in our collection of limestone, wooden and marble fireplaces.
They’ve been used for hundreds of years to provide a focal point of a room, and they’re just as popular now as they’ve ever been. As such, it’s important that it’s regularly cleaned, and if you spill something on it, then it needs cleaning straight away. Don’t worry: if you do it quick enough and don’t let it rest then it shouldn’t damage the marble. Oil-based paints may leave an oily stain after cleaning – refer to the ‘oil’ section of this guide. You can buy poultice or you can make your own depending on what stains you’re trying to remove. Some metal stains, if left for a long time, are permanent and can’t be removed.
Dry with a soft cloth or towel – do not let it air dry as this can cause water marks.
Carefully read the directions on any cleaning products you use and start with small amounts to test. This can be a particularly tough stain to remove so may need to several applications or even help from a professional.
Spread the poultice evenly over the stain so it’s about ½ inch thick, overlapping a little around the sides.
Let the poultic dry and do it’s magic – this will take around 24-48 hours. Remove the poultice, which will have drawn out the stain, and clean the marble with clean (again distilled if possible) water. If the stains are particularly stubborn and ingrained, then it may take several applications before it’s completely gone. Not only that we’ve also got a vast range of electric and gas fires, both modern and traditional to suit all homes.
Blog by fireplaceworld.co.uk
Our brilliant range of cast iron and clay chimineas are high quality, and a must for the garden! So if your fireplace is suffering from a stain or spillage, read on to find the best to get your stone back to its original prestige. It is therefore very important that, before you do anything, you identify what stain you’re dealing with. You could also look into using a commercial rust remover, but make sure the instructions explicitly say it can be used on marble. A liquid paint remover can be used for bigger stains, although you should check the instructions for suitability first. After cleaning, make sure you thoroughly wipe down the surface to dry it and avoid streaks.
For deeper-entrenched stains, carefully applied ph-neutral soap can be used, as long as it is used in moderation. A poultice is basically a soft, damp mass of powder that has been mixed with a little liquid cleaner and left to draw out a stain. During this time, for liquid cleaner should pull the stain into the powder. Sealing your stone can help it resist moisture and other dangers for much longer than unsealed stones.
Inset fires, wall mounted fires or stoves; whatever you’re after, we’ve got it covered.
They provide a practical base and play a major role in setting the decorative tone and style as well. Worse still, by attempting to clean marble, many people actually make the damage worse. Try not to let the marble air dry, as this can cause water spots – especially on flat surfaces such as the mantel and hearth. Marble is a very porous material, and the longer you leave it, the deeper the stain will penetrate the stone. Other solutions that have been suggested include hydrogen peroxide for light marble and acetone for dark marble. Use a spatula or scraper to evenly spread the poultice across your fireplace’s stain, making sure it is applied about a ¼ inch to ½ inch thick.
If the stain hasn’t been removed after this time, create more mixture and repeat. The quality and effectiveness of your sealer varies widely on the brand you use and the type of marble you have, so it is worth talking to a professional to get a recommendation.
Never place mugs or glasses on your hearth or mantle, or at least use a coaster if you do. If your stone is scratched, or a stain is particularly persistent, it is always best to ask for professional help so that you do not damage your stone.
Firepalce Smoke Stain Removal by newbuckchimney.com
Unfortunately, many fireplaces in older homes – and even some in newer homes that have not been properly maintained – have smoke stained bricks around the fireplace opening. This can include the brick, mortar, and masonry surrounding the opening of your fireplace. Thanks in part to the recent safety improvements in the fireplace industry, it is now possible to remove smoke stains from masonry without the use of harsh or toxic chemicals. These products are ecofriendly and safe for both indoor and outdoor use. Without finding the cause of the staining, the smoke stains will only continue to return.
In addition to providing warmth and heat, they also create a beautiful focal point and a place for family and friends to gather.
Unfortunately, they tend to stain any material they come into contact with.
With an older fireplace, the staining is most likely the result of an accumulation of soot over a long period of time. Staining directly above the firebox of a newer fireplace may have been caused by a single event, such as an out of control fire lapping out of the firebox or unsuitable burning materials creating an excess of smoke. In addition, they do not create any harmful odors, allowing you to normally move about your home while they are in use. Our expert technicians will find the source of the smoke, stop it from returning, and completely remove any smoke stains, making your fireplace look and work as good as it did the day it was built.
Clean Marble Fireplace Smoke Stain Fireplace How To Clean Marble End Tables Loccie Better s by loccie.com
If you have a marble end table and do not know how to clean, here are some tips that will come in well.
It will be great if the clean with water and baking soda solution, in a ratio of one part of water for nine bicarbonate.
- The Article As It Originally Appeared – nytimes.com
- Cutting Board With Veggies On Limestone Counter – limestone.com
- Full Frame Shot Of Multi Colored Fabric In Soap Sud – goodhousekeeping.com
- Gallery Collection Marble Fire Surround – direct-fireplaces.com
- How To Clean A Marble Firepalce – fireplaceworld.co.uk
- Smoke Stain Removal Fireplace Shreveport La New Buck Chimney – newbuckchimney.com
- Source – uk.answers.yahoo.com
- Clean Marble Fireplace Smoke Stain Fireplace How To Clean Marble End Tables – loccie.com