The struggle comes with joining two materials together, especially around the corner, to create a flat and continuous finish. Countertop materials with square edges are easier to put together especially if the front edge has a curved finish. The perfect saw blade to cut a laminate countertop is a circular miter saw. The best way to cut the laminate is to lay it face-side down and cut from the back to the front.
How Its Made 196 Countertop Laminate | Duration 4 Minutes 51 Seconds
Keep in mind that any irregularities in the wall surface will cause unsightly gaps along the back edge of the countertop. Use a pencil to draw the cutting line and put masking tape over it as a guideline. Make sure the countertop is secured and well supported on both sides. Remove all the masking tape and smooth the cut edges of the countertop using a plane. For round-edged countertops or with a curved finished edge, it is quite impossible to create a right-angled butt joint. Cut the countertop in the proper size and length and scribe if necessary.
Use a cloth to remove excess sealant as you butt the sections together. So now you have already cut the countertops to the right size and joined surfaces. Clamp along the front edge of the countertops to the cabinets and apply weight from above as you screw through the rail into the underside.
If you want to achieve the best joints, you must use the right techniques on how to cut laminate countertops such as maintaining straight edges that are factory-cut. Laminate countertops are essentially just layers of tightly pressed papers glued together by a sticky and organic substance called resin. Make sure to wear protective pieces of equipment like safety glasses and check if the blade is sharp and clean before you begin cutting. When buying laminate countertops, consider that you will lose some depth because you might have to trim it to fit the wall. Create a guide for trimming by holding a pencil at one side of the wood block and tracing to the other end along the wall. After trimming, reposition the countertop to check if it is the right fit. To avoid any splintering of the laminate surface, place masking tape over the cutting line. Use a straight edge metal ruler along the guideline and score down using a utility knife.
Turn Laminate Into Marble Epoxy Countertop Diy | Duration 30 Minutes 14 Seconds
You can use mending plates or biscuit joiner to create a strong joint. Your best bet is to use a countertop jig or a joining strip. Unlike round-edged countertops, square-edged countertops can be neatly and easily joined together without using a countertop jig.
You can also use two or three mending plates for a stronger joint. The sealant should be applied along the edge of the other countertop. The next thing to do is secure them in place by inserting screws through the countertop brackets. While attaching the units, you will have to ask someone to apply weight to the back. If you have a laminated countertop, you have to cover the edges with laminate strips that are usually supplied by manufacturers. Once they are dry, you can start trimming the edges using a utility knife. You just have to have the right materials, protective pieces of equipment, and a clear understanding of the proper way to do it.
You can make it look like it was done by a professional by making sure the measurements are correct, the surfaces are joined properly and securely, and the countertop has nice finished edges.
Countertop Laminate: How Laminate Countertops Made by countertopspecialty.com
Multiple sheets of paper are used in each layer and the total number of sheets varies and overall thickness depends on what type or grade of laminate is being manufactured. The layers are then pressed together while cooked, which forces all the papers and resins to chemically bond into one plasticized sheet.
These pre-fabricated laminate countertops allow for even faster and easier installation.
And laminate sheeting is used in countless industrial and product applications. Of course, more than three sheets of paper comprise a sheet of laminate. All paper layers are soaked in a resin, which serves as a glue and binder. These sheets can then be cut to size and glued to a plywood substrate on-site for custom laminate countertops or they can be bonded to laminate countertop particle board forms of various lengths that already include the backsplash and edge detail. Of course, it is the most durable, but also pretty stiff and difficult to form or use on anything but a flat surface. For instance installing laminate countertops in an alcove used as a desk or for shelving or possibly a laundry room countertop.
Custom Laminate Countertops by shopcountertops.com
Custom laminate countertops are a durable and beautiful choice for any installation.
When choosing custom laminate countertops one of the first considerations is the choice of color. Whether you are installing a countertop at a new home or replacing an existing countertop the choices are amazing. There are several choices including different edging that is made of the same laminate, beveled edges and even wooden edges. Once you choose the custom laminate countertops you want the next step is measuring. The pieces of the custom laminate countertops were made together out of the same lot of laminate so there are no color variations.
The other choice to make when choosing the best custom laminate countertops is the edging.
My Marble Look Countertops For A Fraction Of The Price | Duration 4 Minutes 58 Seconds
The look of the custom laminate countertops will be very different depending on the edging you pick.
Be sure to provide accurate measurements because this is how the custom laminate countertops will be made. Installation of quality custom laminate countertops is easy. Custom laminate countertops make a kitchen or bathroom that you will be proud of for years to come.
Laminate Countertops by countertopguides.com
These kitchen and bathroom countertops offer excellent versatility and value.
These are often called plastic laminate because the surfaces are plastic. Many are made to mimic the look of more expensive surfaces like marble or granite. Laminate seams can be hidden more easily than most countertop seams. Laminate is not as heat resistant as other surfaces so hot pans should not be placed on laminate countertops. If the laminate surface is scratched, burned or chipped, it is very difficult to repair. They offer attractive finishes in a range of colors sure to match your décor and they do so at very affordable prices. They are great for kids’ bathrooms where they can be quickly sanitized with a disinfectant wipe. Most importantly, you should find the right kitchen countertop that suits your individual needs, and laminate is a good choice for those with a family that includes small children.
Laminate countertops contain a hard particle board core with layers of plastic laminate bonded over the top of it. The kitchen and bathroom countertops come in the widest variety of colors and patterns of any type of countertop. The surface is solid, without pores, so a soapy washcloth or sponge is usually all that is needed.
In the bathroom, if you use hot hair tools, avoid setting them down hot on your laminate bathroom countertops. While there are many attractive laminate colors and patterns, some may still want the natural beauty that more expensive countertop materials such as granite or wood provide. Laminate countertops are one of the best choices for those with a limited budget, a position most homeowners are in. Laminate bathroom and kitchen countertops are easy to clean and don’t harbor harmful germs like porous surfaces do.
How To Paint Laminate Countertops by todayshomeowner.com
Next, wash the surface with soap and water to remove the dust and any grease or grime. Use a brush to apply the counter paint in corners and crevices, but a foam roller is the best way to get a smooth finish on the counter’s flat areas.
This brand of counter paint recommends adding a second coat just 60 minutes after applying the first.
How Its Made Countertop Laminate | Duration 4 Minutes 51 Seconds
Why make a video and write about it and not tell us the paint you used? And funny especially when your daughter gets the upper hand.
The first step to painting laminate countertops is roughing up the surface enough to allow the paint to adhere well.
This doesn’t remove the pattern or color of the laminate countertop; it just removes the surface’s slickness.
Avoid creating lap lines with the roller as you work across the counter. With careful prep and application, the results can be pretty amazing.
How To DIY Laminate Countertops It’Ll Save You SO Much Money by thecraftpatchblog.com
The countertops have to be pulled away from the wall when you place the laminate on, so just keep that in mind. Leave at least two inches of overhang on all sides of the projects. Cover the backs of the long strips of laminate pieces and the countertop sides with an even layer of contact cement. Let glue dry for 30 minutes (check the instructions on the can since some brands may have different dry times). They sell special pre-made edges that you can glue onto your countertops. Using a laminate bit, run your router around the edges of the countertops to trim off the extra laminate. I also suggest doing a test run on scrap material so you don’t mess up on your actual countertops. After all of the edges of your countertops are covered in laminate and routed flush with the wood, it’s time to put glue on the top surface.
Carefully begin pressing the laminate to the wood, leaving plenty of laminate overhanging on all sides. Trim off the extra laminate with your router bit, just like you did on the countertop sides before. and I love the contrast with the white cabinets and dark countertops. One option you could look into is buying pre-built laminate countertops, then cutting them down to fit your kitchen.
How To Install Countertops (Granite / Laminate) Diy | Duration 1 Hour 38 Minutes 49 Seconds
I wrote an entire article about the sink because it had a very detailed installation process.
It has a lot of natural movement, but nothing splotchy or too busy. Cut strips of laminate to cover the edges of the countertop, then cut a big piece to go on top. Trust me on this one… you want to start big and trim it off afterwards. If you want a fancy ogee, bevel or bullnose edge, this is something you might want to look into. So you need to be reeeeeaaaaalllly careful as you start pressing the laminate strips to the edges of the counter. Start on one end and gradually smooth the piece down the entire length of the countertop side.
You may need to do several passes to get the edges flush with the wood. Roll contact cement on both the back of the laminate and the countertop.
I would choose the same color and style of laminate again in a heartbeat. There’s a learning curve using the router and we have a few places where we chewed through the colored layer of laminate or accidentally knicked it. and let me just remind you that we have a lot of countertop in our kitchen. The only thing that bothered me about my edges was that you could see a bit of the white center layer of the laminate. Isn’t that the most amazing thing you’ve ever heard! ? Think of how your granny or great granny cooked and what their kitches looked like! The only thing is my partner is not a carpenter in any sense of the word.
I like “perfect” or as close as possible and he’s happy with “good enough”.
It would really depend on how standard your layout is, etc. You just have to cut it to the right shape and add end caps. I don’t think you could apply new laminate over a rounded or ogee edge.
How To Laminate A Countertop by doityourself.com
Laminates are retailed in a wide variety of styles for many different purposes. Read this article for advice on preparing the work area, sizing and laying laminates, and completing the countertop project. The work space but he smoothed with sandpaper and free of debris before you begin work. Simply press the blade into the material and make a long cut through the top of the surface. Once the laminate and the underlying surface have dried, position the completed laminate material using wooden strips and dowel rods which are spaced every 12-inches. Complete the seams with wax paper, dowel rods, and some more cement.
The general process for manufacturing laminate plastics is to add a resin to multiple paper layers which are subsequently bonded together into a hard surface.
Then repeat this motion until you make a clean cut through the entire sheet of laminate. Joint multiple laminate panels with a seam, which is formed by bonding the pieces at their ends.
The Step By Step Process To Building Laminate Countertops by homeguides.sfgate.com
Laminate countertops are attractive, durable and leave a smaller dent in your remodeling budget than natural or man-made stone. It’s a satisfying do-it-yourself project that yields impressive results. No matter what the material, it’s a good idea to seal any areas that might be exposed to moisture, such as over a dishwasher or underneath a sink.
You’ll also need a flat work space with plenty of ventilation, and a helper or two. It’s a good idea to watch a few video tutorials first to get a feel for the process, especially if you’re relatively new to woodworking. Once you’ve sharpened your skills, and provided you take your time and pay attention to detail, you can give your kitchen a custom look at big savings.
For even greater savings, combine your time and labor with the right tools and materials to build your own laminate countertops. Plywood is strong and stable, but can have hidden flaws that undermine its structure, as well as surface issues that affect how well laminates adhere. While particleboard usually is the choice of most contractors and commercial manufacturers, it’s of a special industrial or countertop grade, so be sure to use the same type if you go this route.
Try out the tools and techniques on a smaller project, such as a workbench or shelf.
How Laminate Countertops Edges Are Made by kuehnbevel.com
Special industrial-grade particleboard is the most popular option, as it offers the best combination of strength, durability and water resistance, and laminate adheres well to its surface. This laminate is glued onto the substrate to create a smooth, durable surface that is easy to maintain, water resistant and an attractive addition to any home.
With modern glue products, this bonding is still exceptionally strong and much easier to fabricate and will last for the life of your countertop. Here’s some insight into how these countertops are made, from expert manufacturers of laminate countertop edges.
What Are Laminate Countertops? by wisegeek.com
For example, cool gray metallic laminate counters provide an alternative to stainless steel. Just some of the many laminate countertop patterns include checks, dots, swirls and assorted geometric abstract graphics. There is almost as much selection in laminate countertop colors, finishes and patterns as there is in fabrics. The contrasting effect of bevel edge countertops can be practical and not just decorative. The post-formed types of laminate counters have rounded edges and are pre-made by machines in lengths that can be adjusted to fit any bathroom or kitchen. The drawback of the laminate countertop in general is that it is not that long lasting.
It reflects your personal style and accents your kitchen with a variety of decorative edges. It seems like a fabulously inexpensive way to update your kitchen, because sadly you are more likely to want to change your countertops before they actually wear out, and my husband likes to wait for things to wear out before they are replaced!
The painting itself seems like it would be easy – no ladders to climb, and not much taping to do!
There are many natural looking colors and patterns of laminates made to resemble granite, slate and other types of stone. They are an affordable option when a bold colorful look is desired. Edges are an important consideration when choosing a laminate countertop. The straight edge type is also called the self-edge, and is the original, boxy one first invented in the 1950s and it leaves a thin brown line around the edges. For instance, a beveled edge that contrasts with the rest of the counter can stand out so it is more visible to the elderly and the visually impaired. A plus in choosing laminate countertops is that they are an inexpensive option to natural and other countertop choices.
Abrasive products should not be used for cleaning as they can ruin laminates. My question would be how labor intensive would sanding the countertop be?
How To Build A Laminate Counter by thisoldhouse.com
Cut the plywood backsplash pieces down to size using a circular saw and straightedge guide. Press the backsplashes tight against the wall, then scribe a cut line along the top of the plywood counter. Use a block plane to trim the build-up strips flush with the counter edges. Spray aerosol contact cement onto the back surfaces of the edge-laminate strips and along the edges of the countertop. Use a belt sander to sand the edge laminate strips flush with the top and bottom of the counter. Repeat the previous five steps to cover the backsplashes with laminate. Use a paint roller to apply contact cement to the top of the counter and to the back side of the countertop laminate. Check to be sure laminate overhangs the counter on all edges and ends, then start pulling out the wood dowels. Use the trim router to cut away the excess laminate from around the edges of the counter, and from the sink cutout. Fasten the backsplash to the rear of the counter using 2-inch screws.
Lift the front edge of the counter and apply silicone adhesive to the tops of the cabinets.
Set the ⅝-inch plywood countertop substrate into place on top of the cabinets. Slip the backsplashes between the rear edge of the counter and the wall. Use a circular saw and straightedge guide to cut the counter down to size; be sure to allow for a 1-inch overhang along the front of the counter, and ¼ inch at the ends. Lay plastic laminate sheet on top of counter and make a rough cut with a laminate router. Trace around the sink template and cut the sink hole in the counter using a jigsaw. Apply a bead of silicone adhesive to the rear edges of the counter. Run a bead of silicone adhesive around the sink cutout, then drop the sink down onto the counter.
DIY Laminate Countertops: 8 Steps by instructables.com
Make sure before you begin that the cabinets are all perfectly level. I had to accommodate a sink in one countertop and a cooktop in another. I just clamp a strip of plywood to a distance offset to cut line by the distance from the edge of the circular saw’s baseplate to the blade.
I did this so if there was any spillage, it would reach the groove and drip on the floor rather than bridge across to the cabinets.
Make sure it is back from the edge so it doesn’t mess up your laminate trimming! Paint contact adhesive on the particle board and on the laminate, and leave to dry for about 10 minutes, until dry to the touch. Stick the end you’re holding down, making sure you have overlap above and below, then carefully press the rest of it. Now, get the laminate trimmer with flush-cut bit installed, and set it up so the bit is just a little more exposed than the depth of the laminate (about 1/16″ or 2 mm).
Like me, you might find yourself with some corners that are not right angles. If you have doubts about the contact cement process, there is an easy way to practice first – try mounting a poster on to plywood. I painted the underside of the edges of the countertop, again to protect against moisture from spillages. Except if there is a sink – put the countertop upside down over the inverted sink on a soft surface and install the sink first. Seal the edges against walls with silicone sealant, and you’re done.
The wood base is very porous and should readily absorb the bubbles. The white glue will be a lot more forgiving give you some working time. It should be sealed tight so no water can ever get in there. Cut from the “wrong” side and the finish is absolutely perfect, couldn’t believe just how good. So yes, it’s quite feasible to butt the two pieces together (usually along a miter to increase the gluing area and to improve the look).
I had one easy (rectangular) countertop and two others that had angles on them. We decided against a back splash – we liked the clean look of kitchens without them. Mark the cabinet outlines from underneath, so you can place the cutouts with confidence (sinks and cooktops come with very clear instructions on exactly how large the cutouts need to be, you just have to make sure they’re in the right place!). You could just as easily make the whole countertop first then make the cutouts later. You may have to clean dried contact cement from the bearing on the bit. I had three to deal with that were about 135° (you can’t see it in any of the photos, but one of the walls of the kitchen is at 45° to the rest).
You have to do one side of the corner at a time, for reasons that will be obvious when you go to do it! The way to deal with it is using dowels to keep the surfaces separated until you’re ready to press them together. Get the contact adhesive on both surfaces, then place dowels every 6″ or so apart on the particle board. Keep going, removing one dowel at a time and pushing down as hard as you can.
Pretty sure it would be impossible once the countertop is installed, unless you’re a masochistic contortionist. As long you don’t buckle the laminate there should be no air bubbles. The groove (and the rest of the underside) is painted to seal it. Laminate is easy on the budget and lasts perfectly fine for years and years with just a little bit of common sense. My question is, how feasible is it to butt two pieces next to one another without the joint being obvious?
DIY Painted Countertops: From Laminate To Granite by hometalk.com
If you have never painted your countertops before, you don’t need to worry about sanding.
To get into the creases and corners, take your fourth sponge that you cut and cut it into a very tiny piece. I preferred less black and lighter countertops though so the majority of my countertops are done using this color. I only added this sparingly in a diagonal pattern randomly across my countertops. You can keep adding paint colors until your counters appear the way you want them. Using your foam brush, apply sealant on the top of the backsplash as well as in the crease just as you did when you were priming. When the bowls are molded part of the counter, how woudl you coat the last protective part as one can’t use a roller on a bowl? We did this in the past before and they held up for two years just fine. I just sand with a 600 grit sandpaper to feather the edges, and reapply the paint and sealer.
However, it is extremely inaccurate when it comes to who carries this product. My countertops are old & really should be replaced but don’t have the money or anyone to do it.
Will find a different product next time as this does not hold up on in a busy kitchen. I hate my granite countertops and would love to paint them a lighter color. Many more people will see your question and answer it from the main question page. I noticed in the first picture the oak colored cabinets and the rest of the pictures they were off white. Will the original color show through with scrapes from food preparation in the kitchen. If you’ve got an ugly counter top like we did, change it up instead of replacing it.
The only additional products you will need is painter’s tape if you choose to use it, a paint tray, and a few paper plates. I also sanded quickly with a 600 grit sandpaper to rough up my previous paint job.
You’ll also want to cut your sponge that came with the kit into four pieces and pour a bit of each paint onto a paper plate. You will want to work on 2 foot sections with this as well because the paint colors blend better when wet. You will want to dab this on over your first color while it’s still wet to help aid in blending.
If you like more of the black coming through, you don’t need to dab it on as thick. I lightly dabbed the white limestone in a diagonal pattern and then went back over it with the inca gold paint (2b) to help blend it in better. Although we recommend adding the colors while the paint is still wet, you can still add more paint once your countertops have dried as well. Also, because you are working in 2 foot sections, you’ll want to keep repeating the painting steps until your entire countertop is covered. Then go back over the section you just did with no extra topcoat, just to ensure that you have eliminated any lap lines. I would recommend for those with a large amount of counter space, to splurge and purchase an additional can of the topcoat. The colors that came in the kit were the inca gold, white limestone, and the brown feldspar. A few chips here and there but overall we were very hard on them and they held up very good! There was very minimal chipping and where it did chip was where we set hot pans directly on the counter (you’re not supposed to do that) and the chips were very tiny. The downstairs countwr top is an ugly blue with white striations running through it.
The downstairs family room, bedroom and bathroom will be my space so would like to fix it up a little to my taste. We were hoping to see an actual sample piece of counter already done. I did my kitchen and bathroom even my bathroom sink 4 years ago still looks great. Does this product hold up with square edges or should they be rounded first? I have oddly shaped counters and it would cost a fortune to replace. How well does it hold up to chips and the occasional knife wielding husband who forgets the cutting board? I have seen so many pictures and posts where a homeowner paints a “faux” granite countertop.
How To Paint Laminate Countertops To Look Like Stone by diynetwork.com
Not only can your counters be a different color, but they can even look like an entirely new material. Be sure the room is properly ventilated as well; have a window open if possible. This is helpful around the sink and corners where space is tight.
At this point, you can fine tune the pattern in specific places to your preference.
This keeps them moist so you can reuse and pounce quickly as you are tweaking the pattern. Allow 24 hours before placing items on countertop to ensure that the paint has cured. You can even sell your house in a few years and recoup this investment.
Twist and turn the brush as you go, using different amounts of pressure. Here are some tips on how to choose a countertop that’s right for you.
- Source – thediyhammer.com
- Buy Granite Cleaner Sealer and Marble Cleaning Products – countertopspecialty.com
- Source – shopcountertops.com
- Dark Laminate Countertop On White Cabinets – countertopguides.com
- Natural Looking Plastic Laminate Countertop – todayshomeowner.com
- Source – thecraftpatchblog.com
- Top Rated Contractor Precision Countertops Inc Style – precisioncountertops.com
- Source – doityourself.com
- Create Custom Designs With Laminate Countertops – homeguides.sfgate.com
- Solid Surface Corian Countertop Edge Options – kuehnbevel.com
- Hilariously Insightful Foreign Words – wisegeek.com
- Exterior View Of The Completed Jamestown Net Zero House – thisoldhouse.com
- Picture Of DIY Laminate Countertops – instructables.com
- Painted Countertops From Laminate To Granite – hometalk.com
- Source – diynetwork.com
- Videos – Countertop Laminate%3a How Laminate Countertops Made