This is done by removing the old/damaged sealer and re-stripping and resealing the limestone floor. Objects that cannot be moved should be covered with a plastic sheet. Ensure that you pay special attention to cleaning along the edges of the walls and the entrances to the room. You don’t need to coat the surface with the solution.


How To Reseal Marble Tile Or Any Natural Stone | Duration 12 Minutes 29 Seconds

Though the floor can be rinsed a few minutes after completing the stripping, it is better to wash-off the floor half way through the project. Once you have stripped about half of the room, stop with the stripping and proceed with comprehensively rinsing the stripped floor. Use the cloth to wipe off any excess sealer compound and buff the limestone floor into a new, shiny surface. Apply the recommended number of coats as directed by the packaged guidelines. The kitchen area was especially grubby and once the island had been removed during recent renovations, the dirty floor really stood out.

However, cleaning with soap is not needed since the chemical stripping is very potent. Open the packaged stripping solution and pour a few drops upon the limestone floor.

Ensure that you spread the acidic stripper across the room and use it in a minimal way. You should have just about enough of chemical stripper to work with when you are brushing the floor. This makes it easier to approximate the amount of stripper solution needed. This is because the acidic stripping solution can permanently scar the flooring surface. Prepare the sealing mixture by pouring some of the sealing solution into a bowl. Stop when it seems that the entire floor is wet with a thin coating of the sealer compound. Wait for about two hours and apply the second coat of sealing compound in the same manner.

Refinishing Travertine Flooring by homeguides.sfgate.com

This natural stone material is derived from limestone, and comes in shades of pink, brown and yellow depending on where it was quarried. Apply a stone floor stripper to the travertine using a paint brush, roller or deck brush. Allow the stripper to remain on the floor for up to two hours, or as recommended in the manufacturers instructions.



Travertine Floor Cleaning, Stripping And Sealing Hampshire, Surrey, East Sussex, Kent.Wmv | Duration 3 Minutes 38 Seconds

Use a mop and water or a wet-dry shop vacuum to remove all stripping products and floor finishes. Spray the floor with water using a spray bottle until the powder transforms into a milky liquid substance. Use a hand sander for small jobs, or rent a weighted floor machine with a natural hair pad for larger areas.

Clean the floor using a wet mop and shop vacuum until all powder, dust and debris have been removed. Choose from various degrees of polish or select a duller, more natural look.

This natural stone material is derived from limestone, and comes in shades of pink, brown and yellow depending on where it was quarried. Restoring travertine to its original appearance requires stripping old finishes and grinding away dull, stained or worn surfaces to reveal the undamaged material hidden below. Cover baseboards and door jambs with painter’s tape to protect these areas from damage while you work. Scrub the floor using a stiff scrub brush or push broom to remove the stripper and any existing sealers or finishes on your floor. Read the instructions on your honing or polishing powder package to determine what grit of sandpaper to use. Add more polishing or honing powder as needed to create the desired finish.

Apply the sealer with a paint brush or roller and allow to dry before walking on the floor.

TRAVERTINE TILE STRIPPING SEALING SYDNEY MELBOURNE CANBERRA PERTH BRISBANE ADELAIDE GOLD COAST by tilecleaners.com.au

They came to her house the next day to have a look at my mum’s tiles. Travertine tiles are quite porous and need a sealer to preserve their beauty and protect them against common staining and other damage that can be caused by your everyday spills.

When your travertine tiles begin to appear dull and start to stain easily, that means your previous sealer is wearing off and your travertine tiles are in danger of permanent damage. Don’t be caught faced with ordinary looking surfaces for the long-term in your home. Our thorough cleaning processes combined with the highest quality products achieve the best and freshest looking travertine tiles, protected and preserved against staining for the longest possible time. You can call us any time, we provide our tile cleaning service in after hours for your convenience. Travertine flooring is a very stylish material that is functional and aesthetically attractive while bringing a very appealing, old-world character to any home or business. Travertine will often appear fibrous or concentric and can come in a white, tan or a cream like colour. Travertine is different to limestone and marble, which are metamorphic rocks, with the main characteristic of travertine being the holes within the stone created as a result of gases escaping as the travertine is formed.

You can then see how any type of water based stain can be absorbed by the travertine tile surface and grout. Water based sealers are easier to apply and remove and also require less drying time. There are two types of impregnating clear sealer, water based sealer & solvent based. Today however, thanks to new technological advancements, it is recommended only to use water based sealer’s, that last much longer and cause less potential damage to health and property. When a topical sealer wears in higher traffic areas, the entire surface usually needs to be stripped and re-sealed.



Travertine Floor Cleaning And Sealing Driffield | Duration 3 Minutes 15 Seconds

This will protect the appearance of the tile, and importantly ensure that there won’t be any dirt, stains or other debris caught under the layer of sealant.

The process of stripping a floor is to ensure that all necessary old and worn sealer is removed; once removed your travertine tiles can be resealed. You will know it’s time to have your travertine floors stripped, cleaned and sealed once they begin to appear dull or “matte” even after you have given them an efficient regular clean. Cleaners® generally use only the highest quality water based products alongside our state of the art cleaning machinery to provide the best cleaning solution without compromising your travertine tiles. Current non-solvent based strippers and techniques are more than adequate.

Materials and agents that present potential health hazards are not in our product portfolio and never have been. If you want your travertine floors to be their cleanest and looking their very best you need to have a professional remove as much of the old sealer as possible. You will have the freshest and cleanest possible travertine floors once we are finished with the process. Travertine tiles stripping and sealing is simply the process of stripping the coating off the travertine floor before resealing it. By stripping and resealing, you can bring back the beautiful, lustrous appearance of your travertine and eliminate the cost of laying new flooring. Our professional team will go through the job processes with you step by step so you know exactly what you’re getting. A new sealer is applied to the dry travertine floor and allowed to set. If you have a high amount of foot traffic or perhaps severe weather conditions(for outdoor tiles), you may experience a shorter lifetime. Once they start showing patchy areas and are staining easily then you should have them resealed. We strongly recommend sealing you travertine tiles to keep their natural look and feel, to protect them against permanent staining and to prevent any future accidental damage.

You will know that your travertine tiles need sealing once you start noticing patchy sealed areas of the floor and/or your travertine tiles are staining easier. Efflorescence is a problem that travertine and most porous tiles can face. The water evaporates leaving the salts on the surface resulting in a whitish coating and ruining its finish. Efflorescence is typically caused by a leakage behind the travertine tiles or through damaged grout lines. Before we begin our work we will measure each room individually, confirm the work to be carried out as well as confirm all costs with you.

I am very satisfied with how patient and highly professional you were with my mother. Thank you some much for your quick help; it was such a relief.

Our years of experience in the field of natural tile protection results in your travertine looking its very best, protected against staining for the longest possible time.



How To Clean And Seal Travertine Floor By Hand | Duration 1 Minutes 27 Seconds

Sealed or not sealed, we will be able to help; our team of tile cleaning professionals will achieve the best possible results for your travertine tiles. Sealant technology has recently taken a giant step forward ensuring unmatched protection and reliability for all natural surfaces.

Give us a call, we are happy to help you with all your travertine tile enquiries, or simply enquire with us online and we will call you back as soon as we can.

Travertine pavers are especially attractive around the swimming pool and surrounds with no two tiles looking the same. Travertine is formed in mineral springs, especially around hot springs, underground rivers and in limestone caves. By the time it is quarried, travertine is naturally beautiful – a smooth, dense stone that exhibits a notable creamy colour that evokes a certain old-world refinement. An impregnating sealer protects the travertine surface and grout from absorbing stains while also resulting in cleaning and maintenance becoming much easier. A penetrating impregnating transparent sealer enters the pores of your stone and, once cured will not change the look of the tile or stone. Topical sealer is also helpful in situations where the old solvent based sealer can not be completely removed or when required to hide certain types of damage. In the past solvent based sealers were more widely used as they used to absorb deeper into the travertine and grout and would also last longer. Solvent based products are more difficult to apply and can create major problems when applied incorrectly as they are very hard to remove. Topical sealer’s (glossy plastic coating over the top of the travertine) are still used on travertine, but these older style sealer’s can trap moisture in the stone and make the surface slippery when wet. To provide the best possible protection from oil and water-based stains; to maintain the look and slip resistance of your travertine and to prevent damaging moisture from being trapped within the stone, it is recommended to seal your travertine with a high quality, invisible, fully breathable impregnating sealer.

If you notice that your travertine tiles are staining easily, it’s a good indication that your previous sealer is wearing off and your travertine floors will need to be resealed immediately to prevent permanent staining. Stone tiles are porous and require more attention than man made tiles, which is why its extremely important to use the correct products and equipment necessary to bring your travertine tiles back to their best possible condition. These products are not messy and won’t damage your travertine tiles or anything else in your home. Once this is done the cleaning process will be carried out and the sealer applied.


Stripping Travertine Floor Lakeway | Www.Tilecleaningaustin.Com | Duration 1 Minutes 59 Seconds

Travertine flooring can look dull and lifeless over time, making it look older and really bringing down the feel of the home. The process includes stripping any previous sealer if it was applied, the travertine is then thoroughly cleaned and neutralised so that it is free of dust, residue and anything else that can affect the new sealer. The newly sealed travertine floor will not only look new again, it will be protected and result in your travertine becoming easier to maintain. It depends on the type of sealer used and the amount of foot traffic the travertine tiles are being exposed to. Sealing your travertine tiles can also depend on the tiles condition. Travertine floors can damage easily, any oily or harsh spills can damage the travertine tiles and penetrate the pores leaving a permanent stain, unreachable by domestic cleaning methods.

They will look their very best for longer and will be easier and more convenient to maintain. The best time to have your travertine tiles sealed is immediately after installation to prevent any accidental staining or damage.

It’s the tendency of the water in the travertine to bring salts from the stone to the surface as it evaporates. The only way to avoid this problem is to seal your travertine tiles with one of our highest quality water resistant sealer’s and to stop the source of the water that is penetrating the tiles, for example a water pipe leak or damaged grout. Efflorescence is a build up of salts and can be removed with efflorescence removers and other specialised cleaning techniques. The efflorescence can be removed but it is important the cause of the efflorescence is resoled. The simplest way to measure is by multiplying the width by the length.

Floor Sealers Vic by floorsealersvic.com.au

Sandstone around a pool area being cleaned ready for sealing. Stripping a floor requires patience and good floor work practices, you can aggressively clean slate to remove dirt deposits and soil, but professional stripping is necessary to remove old coatings.

Stripping is highly recommended for slate floors where there is a build-up of old sealer, flaking is occurring around the edges of the floor, whiteness/moisture has appeared on the floor or if the floor has had water damage.

There are two types of sealers, those that penetrate (penetrating /impregnating sealers) also those which leave a surface coating. The surface coating will alter the appearance of the surface to a differing degrees depending on which product is chosen. Newly layed sandstone crazy paving cleaned, enhanced and sealed to give a natural finish to the sandstone. A driveway which houses 3 units completed with a clear and colour sealer.

The penetrating sealers will leave a natural finish but may alter the colour slightly depending on the type of stone.



Stripping Slate Tile By Pave Cleaner Arizona | Duration 1 Minutes 43 Seconds

We only use quality penetrating sealers that come with a manufacturers warranty, with one particular sealer offering a 15 year warranty, sealed for life. After your stone has been professionally laid and cleaned it is highly recommended that a protective coating (penetrating or surface sealer) is applied to protect your investment. A picture showing the difference, one area gloss finish, one area ready for sealing. Another picture of the covered area sealed with a colour sealer. Driveway cleaned and re-sealed with a colur sealer (charcoal), the side sealed with a clear sealer.

Travertine Floor Cleaning Services by tileandstonemedic.co.uk

It looks great when used for flooring and providing good care is taken it can stand the test of time.

Etching is one of the most common forms of damage to travertine floor tiles. Etching refers to light or pale marks on the surface of the tile which are left behind after such a spillage. Travertine tiling should always be sealed and will usually be polished to some extent, whether that’s a visible shine or a matt finish. If you’ve noticed your flooring becoming generally dull it may need to be repolished to bring it back to life. Sealant is essentially a barrier against day to day wear and as such will gradually wear down in the course of repelling day to day impacts and abrasions.

If unchecked the tiles may go on to chip, or create a tripping hazard. If light coloured grouting has been used it will also show dirt quite readily, this dirt can be trodden into the tiles too and create marks. In the case of etching we would need to assess the scale of the damage first. For travertine floor tiling which has become dull, a simple finishing polish might be all that is necessary to bring life back to the tiles. We’d strongly recommend finishing with a sealer to help guard against staining from minor spillages and general abrasive damage.

In the case of chipped, cracked or seriously damaged tiles we we would need to make a thorough assessment of the damage to the travertine before we decide on a treatment. Repair of travertine floor which has suffered staining or damage from wear and tear can generally be completed in a few hours. Work will be tailored to your needs and will fit around your schedule where possible. Whilst we may use specialist chemicals in the course of our work, we can assure you that by the time we leave all residues will be gone and your tile or stone flooring will be perfectly safe for everyone to use. We also restore many of these surfaces as well, notably natural stone.

That said, it can be vulnerable to damage if not cared for properly. Travertine is easily marked by spillages of common household items like tomato sauce, vinegar, wine, lemon juice and similar liquids. Etching can be a small patch of discolouration, or can cover several tiles depending on the size of the spill. Whatever the case, with regular footfall, occasional moisture and general wear and tear the finishing of the tile will wear down over time. Resealing is another common job to keep travertine tile flooring in good repair. Wearing down of the sealant may leave the travertine tiles looking dull, but it will also leave it far more susceptible to staining, so it’s vital to ensure the sealer is topped up.

Movement in the subfloor can, over time, result in loosening of the tiles. Similarly, wear and degradation of the grouting between the tiles will happen over time and can lead to similar issue.

Generally our technique involves using a specialist polish solution to buff out the visible damage, before applying a finishing polish and a reseal. This polishing can be tailored to your specification depending on your desired finish, for example tiles could be left matt or taken to a higher level of sheen. The sealer should be topped up once a year to maintain this protection. It may be the case that a tile needs to be entirely replaced, in which case we can help with sourcing replacement stone. We always try to fit our repairs around your schedule with an absolute minimum of inconvenience to you and your environment. We avoid bringing loud or bulky machinery into your home and when a job is complete we thoroughly clean up after ourselves to leave your space looking as tidy as it did when we arrived.

Are the chemicals and solutions you use safe around me/my customers/children/pets? We work to extremely high standards of health and safety, conducting proper risk assessments where appropriate and never putting you or anyone else in danger.

Professional Cleaning Sealing Of Floors In The Chester Area by cheshire-cleaning.com

We have been in business since 2001 and have aquired many regular clients in the area. Your floor can also be sealed to hide wear and tear and enhance it’s looks. Your floor can be cleaned and perhaps re-sealed to make it look as new again. Stone floors of this type can be very difficult to maintain and keep clean. This is carried out using specialist machinary which in most cases can make a huge difference often making your floor look like new again. Due to heavy use, they can become dull due to a build up of grime despite regular cleaning and mopping. Re-sealing will also prevent black scuff marks and make it look as new! It is essential to have the floor re-sealed when the original seal has worn off as any staining can be permanent. Machine cleaning will restore your ceramic floor tiles including the grout to as new condition in many cases.

Many types of floors may need periodic cleaning and re-sealing to keep them looking as good as new. After prolonged use due to foot traffic, periodic cleaning maintenance will be required to restore the surface.

Cleaning and sealing of this type of stone floor will not only make them easy to clean, but will also bring out the deep and attractive colours. A build up of grime and cleaning products may not respond to the use of household “off the shelf detergents”.

Seal Travertine Limestone by aldonchem.com

They are characterized by winding, irregular holes in the surface, with the flats finished to varying degrees of smoothness and reflectivity. Depending on the degree of factory polishing, the look and feel vary from non-reflective and a “warm/soft” touch to a high reflectivity and harder feeling finish. Pictures of each of the recommended sealers for this surface type. Yellow arrow shows water drop maintaining a high bead on the sealed side. This filling action will provide less dirt entrapment and easier cleaning. Also, you can test for (and protect against) acidic liquid sensitivity. Your results may vary somewhat from these pictures due to variations in computer display and the surface materials themselves. That, plus different surfaces have different requirements, is why we make the different solids levels.

An old sealer below the surface, even after stripping, will lower the absorption and porosity to some degree.

After simple testing, it proved to be a limestone which is treated very differently than granite. The iron oxide pigments used in concrete products, and the colored clays in clay products, do not fade. Or, for the solvent based penetrating sealers, test spraying lacquer thinner as an alternative to slightly melt and reform the surface and not build too much gloss or create sealer “layering”.

Pick the sealer for the less absorbent areas so you do not have more gloss than desired. The other technique is to keep grout out of the holes to retain the “natural look” of the stone.

They are characterized by winding, irregular holes in the surface, with the flats finished to varying degrees of smoothness and reflectivity. The products you need are listed in the sequence that you would use them. Yellow arrow shows water drop maintaining a high bead on the sealed side. It is a low “matte” type gloss on this piece, but could be no gloss on a more absorbent piece and high gloss on a less absorbent piece. This filling will provide less dirt entrapment and easier cleaning.

Nevertheless, you will be able to see the differences well enough to make good choices. This discussion applies only to the petroleum solvent based sealers. They all work as described, so it is only a matter of which is best for your needs. The more porous the surface, generally the greater the need for the sealer to create a stronger surface. Sometimes it is uneven below the surface and can create an uneven coloring effect with a color enhancing sealer applied later. Sellers use fancy marketing names that can be misleading about the true nature of a surfacing. It was easily restored and protected after a 60 second test. Apply a sufficient quantity to insure below surface penetration & bonding. If a contractor does not agree, feel free to let us find out what is so unusual about this particular project so the contractor does not have to return.

Marble Kare USA by marblekareusa.com

Allow the droplets to stand 5-10 minutes then blot dry with a towel.

The surface still should be sealed with a penetrating sealer. Clean regularly using a product without harsh chemicals specific for shower stalls and wet areas. The surface will also ware terribly, due to easy scratching through out the surface coating on the floor. Penetrating type sealers are recommended for marble and natural stone surfaces.

Some people just have a preference to the type of sealer they want to use. Oil or solvent base blends and water which is the carrier transfers the actual sealing properties into the surface. Is there an advantage to using a solvent (oil) based sealer verses a water based sealer? Excess moisture present during application will cause a reaction and may create a milky affect on the surface which will result in having to strip and re-seal the surface. The purpose is to create reaction time where as the stain can be held at surface level and can be easily cleaned before absorbing in to the porous surface. If you do not know the previous sealer used, it is good to do a test by releasing water droplets in a few areas to determine porosity.

It is recommended cleaning the surface with a neutral ph cleaner prior to application. The product is applied like a penetrating sealer and if applied as specified leaving no excess product on the surface there will be no shine. Vinegar is an acid which will dull the floor surface and will leave the floor full of stains. To clean the surface an intensive cleaner with out harsh chemicals or a mold remover will effectively take care of this problem. Efflorescence is a condition where, as moisture evaporates it brings mineral and salt sediments through the material to the surface. There are different degrees of efflorescence in which various circumstances contribute to it. It’s recommended to seal grout as it is very porous with the exception of 100% epoxy grout which sealer will not adhere to or be needed. Stone is composed of natural minerals which can be easily damaged if cleaned with improper products.

You can test the surface by releasing water droplets on the surface in a few different areas.

If the surface has darkened it should return to its original color in 2-3 minutes. If my marble surface is polished to a high finish, does it still need to be sealed?

Marble and natural stone regardless of the finish is still porous and is susceptible to dirt penetrating the surface and staining. What is the best way to maintain natural stone surfaces in showers and tub areas? The surface should be maintained by using a squeegee to remove water on a regular basis. Topical coatings typically block the pours of natural stone not allowing the stone to breathe. Dirt will also quickly build up on the floors surface making regular cleaning more difficult. Which is better to use, a solvent (oil) based sealer or a water-based sealer? When using a solvent base sealer the surface needs to be completely dry, overnight is recommended.

The type of liquid from a harsh cleaning chemical tends to leave a stain quickly. If there is no coating and water penetrates a penetrating sealer was probably used and should work fine. If a coating type sealer was used it is important to strip the old coating from the surface prior to re-applying another coating type sealer.

A neutral cleaner should be used for cleaning preferably one that has conditioning agents that requires no rinsing. A polished surface may have a blotchy appearance and textured feel to it. Lightly buffing the surface with fine steel wool usually removes the sediment, however there is a possibility the efflorescence may reappear. It is very important when cleaning polished marble and natural stone surfaces, that safe and surface- specific products are used to ensure proper cleaning.

Cleaning Sealing Travertine Shower Tiles by travertine.tilecleaning.co.uk

A black mould had become ingrained in the pores of the shower tiles and the owner wanted it cleaned up before she rented the property out. This worked well and removed all the discolouration and grime leaving the tiles and grout looking almost new.

The client had tried various well known supermarket products to remove the mould and grime from the tile, grout and sealing strip but without success so we got a call. The wall was washed down with fresh water and stubborn areas re-treated. To finish the job we cleaned up the shower head and taps removing any calcium deposits and cleaned the shower screen.

Vinyl Linoleum Stripping Resealing by topfloorpro.com

Depending upon traffic conditions in a given home, the polish will, over time, become worn and dulled. Stripping or removing previously applied polish to your floor should only be performed when routine cleaning no longer works to get your floor looking like new again.

Once all the polish has been removed, the slurry is removed using a wet pick vacuum. This sealer and gloss finish will protect and extend the wear of your floor, reduce marks and scratches and guard against soil penetration and abrasion. Tiles are applied to a smooth, leveled sub-floor using a specially formulated vinyl adhesive that remains tacky but does not completely dry. Vinyl tile is favored over other kinds of flooring materials in high-traffic areas because of its low cost, durability, and ease of maintenance. If properly installed, tiles can be easily removed and replaced when damaged. Some manufacturers have created vinyl tiles that very closely resemble woon, stone, terrazzo and concrete. Tiles free of asbestos are easily distinguished by their size – asbestos tiles were commonly manufactured in 9-inch squares. In the late nineteenth and early twentieth centuries, it was favored in hallways and passages, and as a surround for carpet squares. Linoleum as a floor covering has been largely replaced with polyvinyl chloride (yet still colloquially known as linoleum), which has similar properties of flexibility and durability, but which has greater brightness and translucency and which is relatively less flammable.

A proper polish will be easy to apply, provide full protection from traffic and spills, and be removable with stripping detergents, which won’t damage the floor. Once in place, tiles are typically waxed and buffed using materials and equipment specially formulated for this application.

Vinyl tiles have high resilience to abrasion and impact damage and can be repeatedly refinished with chemical strippers and mechanical buffing equipment.

Tiles can easily be cut and assembled into colorful and decorative patterns. Use of tiles and adhesives containing asbestos were discontinued when asbestos materials were determined to be hazardous. Mastics and adhesives containing low concentrations of asbestos were used into the 1970s and are generally considered non-hazardous because the asbestos is not considered friable. Between the time of its invention in 1860 and its being largely superseded by other hard floor coverings in the 1950s, linoleum was considered to be an excellent, inexpensive material for high use areas. However, most people associate linoleum with its common twentieth century use on kitchen floors.

TRAVERTINE STRIP SEAL SERVICE by stonemaster.com.au

Travertine flooring is an incredibly stylish material that is functional and aesthetically attractive while bringing a very appealing, old-world character to any home or business. Travertine guarantees a beautiful looking area that will last a lifetime. Our knowledgeable and friendly customer service can assist you with your questions and bookings.

You can rest assured your surfaces continue looking great for years to come with our long-term protection, leaving your travertine easier to maintain.

We provide the highest quality service for all your travertine restoration requirements. Our experienced technicians combine years of stone care know-how to provide one the countries highest quality services utilizing state of the art technology with a preference the highest quality non toxic water based products. The high quality products we provide vary according to your specific requirements. Travertine pavers are especially attractive around swimming pools and surrounds with no two tiles looking the same. Give us a call on 0478 085 801 and allow us to take care of everything. Depending on the sealer originally used, stripping and sealing may be required every 2 to 15 years.

How To Refinish Travertine Floor Tiles by doityourself.com

These tiles also cannot be cleaned with basic detergents, because it will damage them. It is important to cover up any surrounding baseboards, vents, or doorways, so that they will not be damaged during the restoration process. If this mixture does not clean the area well enough, use the stone cleanser and repeat the steps. Allow this to soak into the tiles, usually for about 10 to 15 minutes, and then use the rags to clean up the water.

If this is not done perfectly, the new coat will not bond, and the tiles will not blend together as well as they should.

Even though travertine floor tiles may appear to be hard to care for, refinishing the area that has them installed is an easy process that can be accomplished within a few hours. Vacuum the travertine floor tiles with a multi-purpose vacuum, and then tape off the tiles, using plastic where needed. Scrub the floor by hand, with a mixture of citrus free dish soap and a cleaning brush, making sure to take special care in the corners and creases.

Even though the stains to not need to be completely removed at this time, it is important that the floor tiles are clean. To accomplish this, form a barrier around the stain with rags and pour the water into the middle of them. The point of this step is to remove all of the top surface coatings, so that the new coating will be able to bond correctly. Work slowly so that the entire floor is stripped before continuing. Clean up the entire residue that was left by buffing the floor, once again making sure to scrub the corners and creases well.

How Often Should I Seal My Travertine Floors? FAQS by tilecleaners.com.au

We’re happy to answer any questions you may have, and will get back to you as soon as we can. I am very satisfied with how patient and highly professional you were with my mother.

I was very worried about my tiles since they were brand new and very expensive. I sold the office and left your contact details with the new owner for future cleaning. These products are not messy and won’t damage your travertine tiles or anything else in your home.

To help us best serve your enquiry, you can upload any photos that highlight areas of concern. They came to her house the next day to have a look at my mum’s tiles.

I needed to get them sealed and was not sure if it was possible to seal them all.

Tile Cleaning: Stripping Resealing Stone Tiles by tilecleaning101.blogspot.com

The soiled cleaning solution was removed using a wet vacuum and the floor given a thorough rinse using clean water.

Stubborn areas were re-treated using the same process and the floor was left to dry overnight assisted with a turbo air blower.

Sources:

Leave a Reply

Your email address will not be published. Required fields are marked *